- 回首頁 >
- 產品項目 Product item >
- 刮鬍刀塑膠LOGO片零配件
刮鬍刀塑膠LOGO片零配件
刮鬍刀塑膠LOGO片零配件Razor Plastic LOGO Sheet Parts
規格介紹:刮鬍刀塑膠LOGO片零配件Razor Plastic LOGO Sheet Parts
塑膠材質: AS+ABS透明
刮鬍刀塑膠LOGO片尺寸: 依客戶需求
塑膠射出零配件- LOGO片刮鬍刀用
因為射出成型後塑膠產品需做四色~五色的自動印刷, 故塑膠片尺寸需非常精準, 若尺寸跑掉,會造成後續印刷加工程序失敗,另外,由於產品為塑膠透明件,不能有任何黑點或刮痕,故從一開始伴料到生產過程,本廠都特別注重,產品射出成形後,現場工作人員立刻包裝,避免刮傷及空氣灰層附著於塑膠片表面。
*此為代工產品,僅供塑膠製造介紹*
Product:Razor Plastic LOGO Sheet Parts
Material:AS+ABS ( Transparent )
Size:According to customer requirements
Introduction:
Because the product needs to be automatically print in four to five colors, the size of the plastic sheet needs to be very accurate.
If the size is lost, the subsequent printing process will fail.
This product is a transparent plastic part, there should be no black Spots or scratches, from the beginning of the material to the production process, we'll pay attention that.
After the product is injection molded, the on-site staff immediately packs it to avoid scratches and ash layers adhering to the surface of the plastic sheet.
*This is an OEM product, only for the introduction of plastic injection *
更多商品
眼線液筆塑膠射出成型Liquid Eyeliner Pencil Plastic
射出成型眼線液塑膠筆 塑膠筆身較長, 射出成形時需注意筆身直度要夠直, 二次加工的燙金印刷才能提高良率,此外,塑膠筆蓋尺寸要控制好,才能與筆身搭配好,達到密封性效果,否則眼線液具有揮發性,密封效果不好會產生固化問題,另外,圖面中粉紅色塑膠工件為眼線液調節器,這一個成品的模具使用上百顆模仁製做而成,其精準度要求很高,也不可有任何毛邊,反之,眼線液的流量將無法調整控制。 *此為代工產品,僅供精密射出製品介紹* Product:Liquid Eyeliner Pencil Plastic Material:PP Size:According to customer requirements Introduction: The plastic body is long, it is necessary to pay attention to the straightness, that the bronzing printing of the secondary processing can improve the yield. And the size of the plastic cap must be well controlled to match the body well and achieve sealing. Otherwise, the liquid eyeliner is volatile, and the sealing effect is not good, which will cause curing problems. In addition, the pink plastic workpiece in the picture is the liquid eyeliner regulator. The precision is very high, and there must be no burrs, otherwise the flow of the eyeliner will not be able to be adjusted and controlled. *This is an OEM product, only for the introduction of plastic injection *漁具塑膠扣環代工Fishing Gear Plastic Buckle
塑膠代工扣環漁具釣魚用 TPU塑膠材質偏軟,射出後不容易成形,尤其因為此塑膠扣環中間有小孔,然而小孔長度又大於扣環本身厚度的數倍, 故模具開模時需滑塊運做,滑塊運做時成品易變形,塑膠產品不良率高。 *此為代工產品,僅供成形加工介紹* Product:Fishing Gear Plastic Buckle Material:TPU Size:According to customer requirements Introduction: TPU material is soft, and it is not easy to form after injection. Especially there are small holes in the middle of the plastic retaining ring, and the length of the small holes is several times larger than the thickness of the retaining ring itself, so the mold slider needs to be moved when mold is opened, during that moment is easily deformed, and the defective rate of plastic products is high. *This is an OEM product, only for the introduction of plastic injection *塑膠調速遮光器成形Speed Regulating Shutter
塑膠成形調速遮光器 調塑遮光器每個角度的尺寸在射出成形時需很精準,否則會影響電腦數位控制的精準度。*此為代工產品,僅供塑膠射出介紹* Product:Speed Regulating Shutter Material:POM Size:According to customer requirements Introduction: The size of each angle of the speed regulating shutter must be very precise during injection molding, otherwise it will affect the accuracy of digital computer control. *This is an OEM product, only for the introduction of plastic injection *無線電天線塑膠接頭配件Radio Antenna Plastic Connector
塑膠接頭零件-無線電天線 無線電來電時,絕緣效果若做不好的話,會瞬間產生短路,造成無線電使用者受傷或無線電機台損毀,因此天線塑膠接頭是非常重要的安全零件,材質選擇是絕緣效果好的塑膠,再運用塑膠射出的高可塑性,生產出符合尺寸&功能要求的天線接頭(高壓漏電測試規格依客戶自行訂定) *此為代工產品,僅供射出成形介紹* Product:Radio Antenna Plastic Connector Material:PP Size:According to customer requirements Introduction: When the radio calls, if the insulation effect is not do well, a short circuit will occur instantaneously, which will cause the radio user to be injured or the radio station to be damaged. Therefore, the antenna plastic connector is a very important safety part. The material selection is plastic with good insulation effect, and then use high plasticity of plastic injection produces antenna connectors that meet the size and function requirements.(high voltage leakage test specifications are determined by the customer) *This is an OEM product, only for the introduction of plastic injection *針車用精密塑膠齒輪代工Precision Plastic Gears For Sewing Machines
精密塑膠齒輪-針車用 塑膠齒輪最要求尺寸精密,然而POM屬於結晶性塑料,成形後尺寸變化落差很大,如要達成尺寸安定性,需要做內應力消除的程序,在極冷或極熱的環境裡,尺寸安定性好,如果塑膠齒輪在射出成形過程中操作不當,很容易產生噴痕、流痕、縮水或尺寸異動。(POM有分單聚與共聚兩大類,依照成品應用範圍不同而選擇不同類型POM) *此為代工產品,僅供射出成形介紹* Product:Precision Plastic Gears For Sewing Machines Material:POM Size:According to customer requirements Shape:Three-layer gears (bevel gear and spur gear) Introduction: Plastic gears require the most precise dimensions, and POM is a crystalline plastic dimensional change after forming is very large. If want to achieve dimensional stability, is need to do internal stress relief procedures. In extremely cold or extremely hot environments, it's still dimensional stability well. Injection molding, during the process is improper operation, it's easy to produce spray marks, flow marks, shrinkage or dimensional changes. (POM is divided into two categories: monomer and copolymer, and different types of POM are selected according to the application scope of the finished product) *This is an OEM product, only for the introduction of plastic injection *精密無聲齒輪/減震減低干涉聲音塑膠齒輪Precision Silent Gear
精密塑膠齒輪製造-無聲齒輪 TPU塑料選擇有三種: 聚醚類、聚酯類、脂肪族,依照塑膠產品需求的特性選擇最適合的塑膠種類。此塑膠齒輪尺寸的安定性很重要,材質的物性和穩定度也很重要,特別是偏轉及齒形及壓力角、螺旋角度、節圓直徑是否正確。 *此為代工產品,僅供射出成型介紹* Product:Precision Silent Gear Material:TPU+GF ( BASF R2000 ) Size:According to customer requirements Introduction: There are three types of TPU plastic choices: polyether, polyester, and aliphatic. The most suitable plastic type is selected according to the characteristics of plastic products. The stability of the size of the plastic gear is very important, the physical properties and stability of the material are also important. Especially whether the deflection, tooth shape, pressure angle, helix angle, and pitch diameter are correct. *This is an OEM product, only for the introduction of plastic injection *輸出機/印表機精密塑膠齒輪Printer Precision Plastic Gear
塑膠射出代工精密齒輪-印表機/輸出機用齒輪 塑膠齒輪的尺寸控制很重要,齒輪偏轉、齒形及壓力角是否正確,都將影響塑膠件品質,尺寸控制若不好會減損塑膠齒輪壽命,甚至會產生異音,影響辦公室使用輸出機時的工作環境,此外,螺旋齒輪的TAPE要求很嚴苛,故在塑膠代工生產過程都需謹慎處理。 *此為代工產品,僅供塑膠射出介紹* Product:Printer Precision Plastic Gear Material:PC+Teflon Size:According to customer requirements Shape:Two-layer gears ( spur gear and spiral gear) Introduction: The size control of plastic gears is very important. Whether the gear deflection, tooth shape and pressure angle are correct will affect the quality of plastic parts. If the size control is not good, it will reduce the life of product, and produce abnormal noise, which will affect the office and working environment. In addition, the taper requirements of spiral gear are very strict, so we need to be carefully in the injection molding production process. *This is an OEM product, only for the introduction of plastic injection *LED15瓦塑膠外殼 (LED15W)加工LED 15W Plastic Shell (LED 15W)
塑膠零件生產-燈具LED15瓦外殼 此塑膠外殼使用PC白色塑料,由於一整組燈具是由多組模具生產而成,容易產生色差問題,需有一致的射出生產製作流程,才能避免色差問題,導致燈具組裝後顏色不同,而白色塑膠件也較容易顯現瑕疵,故品管人員在品檢時特別注意工件是否沒有黑點、流痕、色料不均等問題,控制好品質。 *此為代工產品,僅供塑膠製品介紹* Product:LED 15W Plastic Shell (LED 15W) Material:PC Size:According to customer requirements Introduction: The product is made of PC of white color. Whole set of lamps is produced by multiple sets of molds, it's easy to cause color difference problems. It's necessary to have a consistent injection production process to avoid color difference problems, resulting in different colors of lamps after assembly. While white Plastic part is prone to defects, so quality control personnel pay attention to has no black spots, flow marks, uneven coloring and other problems during quality inspection. *This is an OEM product, only for the introduction of plastic injection *