漁具塑膠扣環代工
點擊圖片放大商品名稱:
規格介紹:
漁具塑膠扣環代工Fishing Gear Plastic Buckle
規格介紹:漁具塑膠扣環代工Fishing Gear Plastic Buckle
塑膠材質: TPU
漁具塑膠扣環尺寸: 依客戶需求
詳細介紹:
塑膠代工扣環漁具釣魚用
TPU塑膠材質偏軟，射出後不容易成形，尤其因為此塑膠扣環中間有小孔，然而小孔長度又大於扣環本身厚度的數倍, 故模具開模時需滑塊運做，滑塊運做時成品易變形，塑膠產品不良率高。
*此為代工產品，僅供成形加工介紹＊
Product：Fishing Gear Plastic Buckle
Material：TPU
Size：According to customer requirements
Introduction：
TPU material is soft, and it is not easy to form after injection.
Especially there are small holes in the middle of the plastic retaining ring, and the length of the small holes is several times larger than the thickness of the retaining ring itself, so the mold slider needs to be moved when mold is opened, during that moment is easily deformed, and the defective rate of plastic products is high.
*This is an OEM product, only for the introduction of plastic injection *
更多商品
塑膠調速遮光器成形Speed Regulating Shutter
塑膠成形調速遮光器 調塑遮光器每個角度的尺寸在射出成形時需很精準，否則會影響電腦數位控制的精準度。＊此為代工產品，僅供塑膠射出介紹＊ Product：Speed Regulating Shutter Material：POM Size：According to customer requirements Introduction： The size of each angle of the speed regulating shutter must be very precise during injection molding, otherwise it will affect the accuracy of digital computer control. *This is an OEM product, only for the introduction of plastic injection *
無線電天線塑膠接頭配件Radio Antenna Plastic Connector
塑膠接頭零件-無線電天線 無線電來電時，絕緣效果若做不好的話，會瞬間產生短路，造成無線電使用者受傷或無線電機台損毀，因此天線塑膠接頭是非常重要的安全零件，材質選擇是絕緣效果好的塑膠，再運用塑膠射出的高可塑性，生產出符合尺寸&功能要求的天線接頭（高壓漏電測試規格依客戶自行訂定） *此為代工產品，僅供射出成形介紹* Product：Radio Antenna Plastic Connector Material：PP Size：According to customer requirements Introduction： When the radio calls, if the insulation effect is not do well, a short circuit will occur instantaneously, which will cause the radio user to be injured or the radio station to be damaged. Therefore, the antenna plastic connector is a very important safety part. The material selection is plastic with good insulation effect, and then use high plasticity of plastic injection produces antenna connectors that meet the size and function requirements.(high voltage leakage test specifications are determined by the customer) *This is an OEM product, only for the introduction of plastic injection *
針車用精密塑膠齒輪代工Precision Plastic Gears For Sewing Machines
精密塑膠齒輪-針車用 塑膠齒輪最要求尺寸精密，然而POM屬於結晶性塑料，成形後尺寸變化落差很大，如要達成尺寸安定性，需要做內應力消除的程序，在極冷或極熱的環境裡，尺寸安定性好，如果塑膠齒輪在射出成形過程中操作不當，很容易產生噴痕、流痕、縮水或尺寸異動。(POM有分單聚與共聚兩大類，依照成品應用範圍不同而選擇不同類型POM) *此為代工產品，僅供射出成形介紹* Product：Precision Plastic Gears For Sewing Machines Material：POM Size：According to customer requirements Shape：Three-layer gears (bevel gear and spur gear) Introduction： Plastic gears require the most precise dimensions, and POM is a crystalline plastic dimensional change after forming is very large. If want to achieve dimensional stability, is need to do internal stress relief procedures. In extremely cold or extremely hot environments, it's still dimensional stability well. Injection molding, during the process is improper operation, it's easy to produce spray marks, flow marks, shrinkage or dimensional changes. (POM is divided into two categories: monomer and copolymer, and different types of POM are selected according to the application scope of the finished product) *This is an OEM product, only for the introduction of plastic injection *
精密無聲齒輪/減震減低干涉聲音塑膠齒輪Precision Silent Gear
精密塑膠齒輪製造-無聲齒輪 TPU塑料選擇有三種: 聚醚類、聚酯類、脂肪族，依照塑膠產品需求的特性選擇最適合的塑膠種類。此塑膠齒輪尺寸的安定性很重要，材質的物性和穩定度也很重要，特別是偏轉及齒形及壓力角、螺旋角度、節圓直徑是否正確。 *此為代工產品，僅供射出成型介紹* Product：Precision Silent Gear Material：TPU+GF ( BASF R2000 ) Size：According to customer requirements Introduction： There are three types of TPU plastic choices: polyether, polyester, and aliphatic. The most suitable plastic type is selected according to the characteristics of plastic products. The stability of the size of the plastic gear is very important, the physical properties and stability of the material are also important. Especially whether the deflection, tooth shape, pressure angle, helix angle, and pitch diameter are correct. *This is an OEM product, only for the introduction of plastic injection *
輸出機/印表機精密塑膠齒輪Printer Precision Plastic Gear
塑膠射出代工精密齒輪-印表機/輸出機用齒輪 塑膠齒輪的尺寸控制很重要，齒輪偏轉、齒形及壓力角是否正確，都將影響塑膠件品質，尺寸控制若不好會減損塑膠齒輪壽命，甚至會產生異音，影響辦公室使用輸出機時的工作環境，此外，螺旋齒輪的TAPE要求很嚴苛，故在塑膠代工生產過程都需謹慎處理。 *此為代工產品，僅供塑膠射出介紹* Product：Printer Precision Plastic Gear Material：PC+Teflon Size：According to customer requirements Shape：Two-layer gears ( spur gear and spiral gear) Introduction： The size control of plastic gears is very important. Whether the gear deflection, tooth shape and pressure angle are correct will affect the quality of plastic parts. If the size control is not good, it will reduce the life of product, and produce abnormal noise, which will affect the office and working environment. In addition, the taper requirements of spiral gear are very strict, so we need to be carefully in the injection molding production process. *This is an OEM product, only for the introduction of plastic injection *
LED15瓦塑膠外殼 (LED15W)加工LED 15W Plastic Shell (LED 15W)
塑膠零件生產-燈具LED15瓦外殼 此塑膠外殼使用PC白色塑料，由於一整組燈具是由多組模具生產而成，容易產生色差問題，需有一致的射出生產製作流程，才能避免色差問題，導致燈具組裝後顏色不同，而白色塑膠件也較容易顯現瑕疵，故品管人員在品檢時特別注意工件是否沒有黑點、流痕、色料不均等問題，控制好品質。 *此為代工產品，僅供塑膠製品介紹* Product：LED 15W Plastic Shell (LED 15W) Material：PC Size：According to customer requirements Introduction： The product is made of PC of white color. Whole set of lamps is produced by multiple sets of molds, it's easy to cause color difference problems. It's necessary to have a consistent injection production process to avoid color difference problems, resulting in different colors of lamps after assembly. While white Plastic part is prone to defects, so quality control personnel pay attention to has no black spots, flow marks, uneven coloring and other problems during quality inspection. *This is an OEM product, only for the introduction of plastic injection *
燈具塑膠裝飾環配件Lamp Shade Ring
塑膠燈具配件-裝飾環 此塑膠件在射出成型後需電鍍二次加工，由於只有局部塑膠件需電鍍，只有工件表面要電鍍，側面和底部都不能有電鍍，包含崁合肋勾處也不可有任何電鍍色，故特別選用真空電鍍，搭配專用治具，讓產品不會在電鍍製程中變形，此外，塑膠件外觀面容易在電鍍時產生雜質造成不良，本廠為了達到高品質，二次加工後100%全檢。 *此為代工產品，僅供塑膠特性介紹* Product：Lamp Shade Ring Material：ABS Size：According to customer requirements Introduction： This product needs to be electroplated for secondary processing after injection molding. Only the part of top need to be electroplated, on the side and the bottom can't to be electroplated, including the rib hook. For Vacuum electroplating is used with special fixtures, that the product will not be deformed during the electroplating process. The plastic is easy to produce impurities during electroplating, in order to achieve high quality, we conducts 100% full inspection after secondary processing. *This is an OEM product, only for the introduction of plastic injection *
針車用穿線器塑膠射出設計Needle Threader Design For Sewing Machine
Product：Needle Threader Design For Sewing Machine Material：ABS
