- 回首頁 >
- 產品項目 Product item >
- 材料箱300
材料箱300
商品名稱:
材料箱300Material Box
材料箱300Material Box
詳細介紹:
Product:Material Box
Material:PP
Size:According to customer requirements
Introduction:
*This is an OEM product, only for the introduction of plastic injection *
更多商品
傳動齒輪Transmission Gear
Product:Transmission Gear Material: Size:According to customer requirements Introduction: *This is an OEM product, only for the introduction of plastic injection *原廠汽車配件-車門開關零件(安全部品)Original Auto Parts -Door Switch Parts ( s afety parts )
安裝於原廠汽車門把,屬於安全性功能件。 汽車車門塑膠配件,屬於安全結構件。需在受到任何撞擊時,車門盡可能維持可開啟。 塑膠射出汽車配件時 考量公差及配合件幾何公差,塑膠模具精密度,也相對重要。 塑膠材質 汽車塑膠材質採用指定專用塑膠材料。 *此為代工產品,僅供塑膠射出成型介紹* Product:Original Auto Parts ---Door Switch Parts ( s afety parts ) Material:POM Introduction: Installed on the car door handle, it's safety part. The doors must be able to open as much as possible at the event of any impact.Plastic injection, need to consider tolerances and geometric tolerances of mating parts, and the precision of plastic molds. Material-customer-specified special plastic materials. *This is an OEM product, only for the introduction of plastic injection *原廠汽車配件-車門窗戶端蓋(左右鏡射)Original Auto Parts -Door And Window End Caps
*此為代工產品,僅供塑膠射出成型介紹* Product:Original Auto Parts ---Door And Window End Caps Material:PP Introduction: *This is an OEM product, only for the introduction of plastic injection *原廠汽車配件-座椅滑軌端蓋Original Auto Parts -Seat Rail End Cap
*此為代工產品,僅供塑膠射出成型介紹* Product:Original Auto Parts ---Seat Rail End Cap Material:PP Introduction: *This is an OEM product, only for the introduction of plastic injection *原廠汽車配件-車門控制板塑膠零件Original Auto Parts -Door Control Panel Plastic Parts
塑膠控制板-汽車車門用配件 控制板在汽車車門塑膠零配件屬於安全部品(安全零件),必需在任何情況下盡可能維持汽車車門可開啟狀態。塑膠汽車零件需在氣候溫度零下40度至80度時,不能影響其功能性。射出代工此汽車零配件的尺寸要求非常精密,此外,射出成形時,也需在有限的公差內掌控好輪廓平行度(滑軌輪廓),平面度,垂直度,同心度,再搭配本廠2.5次元影像量測儀量測。塑膠產品有特殊物性要求,選用高階POM塑膠材質。 *此為代工產品,僅供精密塑膠射出介紹* Product:Original Auto Parts ---Door Control Panel Plastic Parts Material:POM Size:According to customer requirements Introduction: Plastic Control Panel - Parts for Auto Doors The control panel in the car door are safety parts, and the doors must be able to open as much as possible at any circumstances. In the climate temperature is minus 40 degrees to 80 degrees, plastic auto parts should not affect their functionality The size requirements of this auto parts are very precise. Injection molding, it is also necessary to control the contour parallelism (slide rail contour), flatness, verticality, concentricity within a limited tolerance, and then match the 2.5D vision measuring system measuring instrument measurement. Plastic products has special physical property requirements, and high-end POM plastic materials are selected *This is an OEM product, only for the introduction of plastic injection *原廠汽車配件-兒童車門安全鎖Original Auto Parts -Child Door Safety Lock
塑膠汽車零配件-兒童安全鎖汽車車門 汽車車門屬於重要的安全汽車零件,對於塑膠射出工件的精密度非常要求。在零下40度至80度的氣候環境下,塑膠汽車配件需維持其塑膠功能性。射出成形時,除了控制尺寸在有限的公差外(輪廓平行度&平面度&垂直度&同心度),塑膠件的外觀也不能有銳角或毛邊,避免任何乘客或兒童接觸時刮傷。精密塑膠射出有特殊物性要求,選用高階POM塑膠材質。 *此為代工產品,僅供精密塑膠射出介紹* Product:Original Auto Parts ---Child Door Safety Lock Material:POM Size:According to customer requirements Introduction: The car door is an important safety auto part, and the precision of the plastic injection workpiece is very demanding. In the climate environment of minus 40 degrees to 80 degrees, plastic auto parts need to maintain their functionality. Injection molding, in addition to controlling the dimensions within limited tolerances (contour parallelism & flatness & perpendicularity & concentricity), the appearance of the plastic parts must not has sharp angles or burrs to avoid any scratches by passengers or children. *This is an OEM product, only for the introduction of plastic injection *腳踏車反光片(通過德國檢驗認證)Bicycle Reflector ( certified by German inspection )
塑膠反光鏡片 透過固定光源及距離,當光束照在塑膠反光鏡片時產生折射,其折射角度及折射率,均須須達到標準塑膠射出成型,須考量到產品結晶性,折射率及平整度!需適當調整塑膠射出條件。 (此產品通過德國認證,非坊間玩具類或不合格品) *此為代工產品,僅供精密塑膠射出介紹* Product:Bicycle Reflector ( certified by German inspection ) Material:PMMA Introduction: With a fixed light source and distance, when the light beam hits the plastic reflective lens, it will refract, and the refraction angle and refractive index must meet the standard. Injection molding, the crystallinity, refractive index and flatness of the product must be considered! Injection conditions need to be adjusted appropriately. (This product is certified by Germany, not a toy or substandard product) *This is an OEM product, only for the introduction of plastic injection *腳踏車後車燈-紅Bicycle Rear Light
*此為代工產品,僅供塑膠射出成型介紹* Product:Bicycle Rear Light Introduction: *This is an OEM product, only for the introduction of plastic injection *