伺服器塑膠外殼零件代工
點擊圖片放大商品名稱:
規格介紹:
伺服器塑膠外殼零件代工Server Plastic Shell Parts
規格介紹:伺服器塑膠外殼零件代工Server Plastic Shell Parts
塑膠材質: PBT + GF30
伺服器外殼尺寸: 依客戶需求
詳細介紹:
塑膠廠代工塑膠外殼-伺服器
做為電腦硬體周邊零件的伺服器，消費者在選購時除了參考功能外，也會注意外觀，所以在加工製造時，品管人員會檢查塑膠件顏色是否均勻，是否有流痕、毛邊、黑點等。塑膠材質選用PBT，雖然硬度夠，但塑膠射出成形中容易變形&脆裂，需從射出條件參數做調整才能控制好尺寸，尺寸不精確的話會使產品產生噪音或操作不順。
*此為代工產品，僅供塑膠射出介紹*
Product：Server Plastic Shell Parts
Material：PBT + GF30
Size：According to customer requirements
Introduction：
As a server for computer hardware peripheral parts, consumers will not only refer to the function, and also pay attention to the appearance.
Quality inspectors will check the color of the plastic parts is uniform and the flow marks or burrs, black spots.
Material is PBT, although the hardness is sufficient, but is prone to deformation and brittle cracking during injection molding.
It's necessary to adjust the parameters of the injection conditions to control if the size is not accurate, the product will produce noise or operate poorly.
*This is an OEM product, only for the introduction of plastic injection *
更多商品
遙控直升機主齒輪-精密塑膠齒輪RC Helicopter Main Gear-Precision Plastic Gear
塑膠齒輪精密射出主齒輪--遙控直升機 此塑膠齒輪尺寸安定性很重要，特別是偏轉、齒形、壓力角都需精密射出成形，然而，此主齒輪的外徑較大(塑膠齒輪外徑長達14cm)， 外徑尺寸越大，成形越困難，如射出成型尺寸控制不當，則有可能造成遙控在飛機飛行時，主齒輪破裂，導致失去動力而摔機。另外，螺旋齒輪的TAPE（錐度）要求也很嚴苛，射出代工時每個環節都需特別注意。POM屬於結晶性塑料，射出成形後變化落差很大，如要達成尺寸安定性的話，在塑膠射出的製程中，需要做內應力消除的程序，在極冷或極熱的氣候環境裡，尺寸安定性才會好。 *此為代工產品，僅供射出製程介紹* Product：RC Helicopter Main Gear-Precision Plastic Gear Material：POM Size：Outer diameter 14cm Shape：Spiral gear Introduction： The dimensional stability of the plastic gear is very important, especially the deflection, tooth shape, and pressure angle all require precise injection molding. The outer diameter of the main gear is large (the outer diameter is 14cm), and the larger of outer diameter is more difficult to form. If the size is not properly controlled, it may cause the gear to break when it aircraft is flying, resulting in loss of power and the aircraft falling. The TAPE (taper) requirements of the helical gear is also very strict, we have to pay attention each link during the injection molding. POM is a crystalline plastic dimensional change after forming is very large. If want to achieve dimensional stability, is need to do internal stress relief procedures. In extremely cold or extremely hot environments, it's still dimensional stability well. *This is an OEM product, only for the introduction of plastic injection *
行車記錄器塑膠外殼配件代工Driving Recorder Plastic Shell
塑膠射出汽車配件-行車記錄器外殼 汽車塑膠零配件為了因應不同環境氣候，對外氣溫要求需達到-40度~+80度不變形、不脆裂 (南半球北半球氣溫差異大)以及防水要求，然而ABS塑料太軟，PC塑料又太硬，故射出成型時塑膠材質選用PC+ABC以符合要求。此外，此塑膠外殼螺母與鏡頭的螺紋需有適當的扭力，且螺紋和螺母在組裝時亦不能產生塑膠屑，代工此精密塑膠產品我們對扭力值、真圓度、表面粗度都特別要求。 *此為代工產品，僅供精密塑膠射出介紹* Product：Driving Recorder Plastic Shell Material：PC+ABS Size：According to customer requirements Introduction： In order to adapt to different environmental climates, auto plastic components need to meet the requirements of -40 degrees to +80 degrees without deformation, brittle cracking waterproof requirements. Material ABS is too soft, and PC is too hard, so plastic material is used PC+ABC to meet the requirements. The thread of the plastic housing nut and the lens must has proper torque, and the thread and nut should not produce plastic chips during assembly. We have special requirements for torque value, roundness, and surface roughness for this product. . *This is an OEM product, only for the introduction of plastic injection *
汽車倒車影像鏡頭組塑膠零配件Car Reversing Camera Lens Plastic Parts
射出代工汽車零配件-倒車影像鏡頭組 許多汽車在出廠時已加裝倒車影像系統，而為了符合不同氣候的需求，塑膠材質使用軟硬度最適當的PC+ABS。外殼內孔裡的螺紋不論是對扭力值、真圓度都非常要求，此塑膠外殼的表面粗度也很重要，除了美觀外，更重要的是在螺紋和螺母組裝時較順暢且不會產生塑膠屑。 *此為代工產品，僅供精密射出技術介紹* Product：Car Reversing Camera Lens Plastic Parts Material：PC+ABS Size：According to customer requirements Introduction： Many cars have been equipped with a reversing camera system before leaving the factory, in order to meet the needs of different climates, the material is used PC+ABS with the most appropriate hardness. The thread in the inner hole of the shell is very demanding on the torque value and roundness, the surface roughness of the plastic shell is also important. In addition to aesthetics, it's more important that the thread and nut are assembled smoothly and without plastic chips. *This is an OEM product, only for the introduction of plastic injection *
隨身wifi塑膠外殼成形Portable Wi-Fi Plastic Shell
隨身wifi外殼射出成形塑膠配件 隨身wifi塑膠外殼在射出代工時我們較注意塑膠殼外觀、色澤、表面粗度，這些是消費者在選購產品時最直接注意到的，此外，尺寸也需控制好，組裝後才不會有過大的間隙，甚至影響產品功能。 *此為代工產品，僅供塑膠製作介紹* Product：Portable Wi-Fi Plastic Shell Material：PC+ABS Size：According to customer requirements Introduction： We pay more attention to the appearance, color, and surface roughness of the shell for portable Wi-Fi when injection molding. Couse that things is consumers notice most directly when purchasing products. The size needs to be well controlled, that it will not has large gaps, lead to affect the product function after assembly. *This is an OEM product, only for the introduction of plastic injection *
植牙牙釘塑膠保護套射出Dental Implant Nail Plastic Protector
塑膠零配件製造-醫療用保護套 為了符合各類醫療的高溫殺菌不會變形, 故塑膠材質的選擇很重要, 而PSU具有耐高溫、尺寸較安定的特性，而且不會釋放荷爾蒙干擾素 (造成男人女性化，女人男性化) ，例如奶瓶多數選用PSU材質此特性，此醫療級塑膠保護套除了真圓度和尺寸要精密外，因為產品是放在口腔內牙齒上，本廠在射出生產製程中特別注重乾淨度，產品符合美國FDA認證要求。 *此為代工產品，僅供精密射出介紹* Product：Dental Implant Nail Plastic Protector Material：PSU Size：According to customer requirements Introduction： Medical protective case In order to meet the high-temperature sterilization of various medical treatments without deformation, choice of the material is very important, PSU has the characteristics of high temperature resistance, stable size and does not release the hormone interferon. For example, most of the milk bottles are made of PSU material. This product should be precise to control the roundness and size. This product is placed on the teeth in the oral cavity, we pay special attention to cleanliness in the injection molding process, and the product conforms to the United States. FDA certification requirements. *This is an OEM product, only for the introduction of plastic injection *
醫療級手術用除毛刀片塑膠盒Medical Grade Surgical Hair Removal Blade Plastic Box
塑膠盒射出成形-醫療等級手術除毛刀片用 醫療級塑膠盒需有一定的耐溫度，塑膠盒才不會在殺菌過程中產生變化，在塑膠射出生產線上，除了控制尺寸和檢視塑膠盒外觀外，本廠也維持產品乾淨度。 *此為代工產品，僅供塑膠製程介紹* Product：Medical Grade Surgical Hair Removal Blade Plastic Box Material：PC 、ABS 、POM、PA Size：According to customer requirements Introduction： Medical-grade plastic boxes need to have a certain temperature resistance that the plastic boxes will not change during the sterilization process. On the injection molding line, has to controlling the size and checking the appearance, we also maintains the cleanliness of the products. *This is an OEM product, only for the introduction of plastic injection *
材料箱300Material Box
Product：Material Box Material：PP Size：According to customer requirements Introduction： *This is an OEM product, only for the introduction of plastic injection *
傳動齒輪Transmission Gear
Product：Transmission Gear Material： Size：According to customer requirements Introduction： *This is an OEM product, only for the introduction of plastic injection *
